English > Companies
Precision Products-100% Hand made U.S. products!
name:
--------------------------------------------------------------------------------
Precision Products are here!
T-Shirts pics throught tread
WEBSITE NOW UP! www.precision-products.info
Precision Super Tough Pegs 1.5" Knurled and Griptape versions NOW HERE! PICS ON PAGE 17
Steel barcaps are almost non-existent these days, so I decided to come out with a line of modern and extremely durable barcaps and gripstops. Sold in pairs.
New! Precision Super Tough Plastic Barcaps:
-Made from some of the strongest plastic material ever made!
-Smooth semi-rounded inner edge and more of a fuller rounded outer edge
-7/8 in. Now updated and available in black
-Single small stainless steel set screw in oxide black
-Less than half the weight of nylon and much more than twice as strong!
-A small lip at the end of the inside where the barcap stops sliding on.
-Self lubricating, so they "slide" on many surfaces
-Weight 16.7g or 0.58oz lightest barcaps I know to have ever been made!
-Made in USA
-AVAILABLE NOW!
Pics Posted!
New! Precision Super Tough Plastic Gripstops:
-7/8 in.
-These come in all black
-Made in the same super strong plastic material as the Precision Super Tough Barcaps, Ultra Lightwieght!
-These have semi-rounded edges
-Weight 7.1g or 0.25oz Ultra Lightweight
-Made in USA
-AVAILABLE NOW!
Pics Posted!
New! Precision Revised Steel Barcaps!
-Available in 7/8 only
-Available in silver only
-Semi-rounded on the on the backside and more rounded on the front
-Very low profile and will last Extremely long!
-Weight 80.7g or 2.9oz
-Made in USA
-AVAILABE NOW!
Pics posted!
New! Precision Super Tough Pegs:
-Made from some of the strongest plastic material ever made!
-Based off of all rider feedback and personal preference
-Knurled with rounded end for pivoting and tapered in the rear for fork clearance and to allow more room to pull your rear wheel back without the pegs going over the dropouts.
-1.75" wide by 4.5" in length. NOW AVAILABLE IN 1.5" KNURLED OR W/GIRIP TAPE PICS ON PAGE 17!
-Incredibly Strong material that does not shred and make sharp edges that cut your hands
-Material has a self-lubricating quality so are extremely "ground friendly" and "slides" on all surfaces!
-Machined interior with a thicker width at the base and front of the peg for weight reduction
-Radioused internally at the base and at the front of peg
-SUPER LIGHT WEIGHT and EXTREMELY DURABLE!
-Available in black 3/8 axle hole only
-UNTERGOING THOURGH TESTING!
-Made in USA
PICS POSTED ON THIS PAGE AND PAGE 12!
NEW! Precision 3-IN-1 Stem:
This stem allows you to chose from 3 legths in one stem!
-26mm, 35mm, or 38mm all in one stem!
-Weight: 26mm: 185.9g or 6.5oz. 35mm:216.5g or 7.6oz. 38mm: 225.6g or 7.9oz.
-4 additional longer bolts included for the 38mm option
-Available in black only
-Made in USA
Pics posted!
WEBSITE NOW UP! www.precision-products.info Or email: marceltreblay@yahoo.com
Thanks!
Precision Products riders: -Dylan Worsley
Videos posted within the tread -Coco Dela Cruz
More pics posted throught the tread.
TOflat:
Decent looking pictures, but two screws in bar ends work much better than one. That and I hope the prices for the two are mixed up, otherwise that plastic bar end must be made out of PEEK or some other ridiculously expensive aircraft grade plastic.
name:
--- Quote from: TOflat on February 21, 2010, 07:58:48 AM ---Decent looking pictures, but two screws in bar ends work much better than one. That and I hope the prices for the two are mixed up, otherwise that plastic bar end must be made out of PEEK or some other ridiculously expensive aircraft grade plastic.
--- End quote ---
They are made out of a material that is very similar to polyurethane, what skate board wheels are made out of. So you know they will last. They are actually lighter though and have a teflon coat so they slide easy if you messup on a hiker or backpacker.
name:
--- Quote from: TOflat on February 21, 2010, 07:58:48 AM ---Decent looking pictures, but two screws in bar ends work much better than one. That and I hope the prices for the two are mixed up, otherwise that plastic bar end must be made out of PEEK or some other ridiculously expensive aircraft grade plastic.
--- End quote ---
I can get them made with 2 bolts, but with one you have the ability to rotate them if needed and not risk grinding your allen bolt down so you cant get the allen key in the slot.
TOflat:
Two screws at 90 degrees each would eliminate the risk of over tightening the single screw. And I think I have an idea of the plastic that's being used. I'd like to get my hands on it myself. (I think it's called Durathane in the skateboard industry, pretty neat stuff).
As I said, I like the look of em. When I do a run of my own though I'm making full barends with capped holes. I've had bad experience with uncapped ends. Best of luck!
Navigation
[0] Message Index
[#] Next page
Go to full version